[C320-list] Inside Table And Pedistal

[Kirk McCullough]

Bill

Nope, no screws. The screwed on flange on table top is press fitted onto the 
post. I simply pull up on the table top and the post pulls out of the 
flange. No need to unscrew anything. Now I'm not sure this compression fit 
is designed to pull out, but it does and it works work well. When i put the 
table top back in place it always presses down nice and tight.


Just try pulling straight up on the table top and see if it separates from 
the post. Good Luck

Kirk
----- Original Message ----- 
From: "Bill Culbertson" <billculb_a2 at yahoo.com>
To: "C320-List" <c320-list at catalina320.com>; <catalina at thehares.com>
Sent: Friday, February 23, 2007 3:04 PM
Subject: Re: [C320-list] Inside Table And Pedistal


So you unscrewed it from the underside of the table?  Seems reasonable.  Or 
was your post attached the the table top some other way.

 -bill


----- Original Message ----
From: Kirk McCullough <kirk.mccullough at telus.net>
To: catalina at thehares.com; C320-List <c320-list at catalina320.com>
Sent: Friday, February 23, 2007 3:39:18 PM
Subject: Re: [C320-list] Inside Table And Pedistal


Mine comes off at the table top where it connects to the post and does not
involve using the screw knob at all. IE) the post stays in position and can
be lowered to get it out of the way. This allows you walk around room, much
better when moving batteries around. It was a very handy arrangement for me
when I installed a dedicated starting battery just forward of the strbd
house bank.

It may be that some of the tables out there will not separate at this joint.

Kirk

Boomerang. #124
----- Original Message ----- 
From: "Jeffrey Hare" <Catalina at thehares.com>
To: "'C320-List'" <c320-list at catalina320.com>
Sent: Friday, February 23, 2007 6:48 AM
Subject: Re: [C320-list] Inside Table And Pedistal


>
> FYI:  We've had this discussion before and one important point to note is
> that only *SOME* tables lift off as stated.  Mine, for instance has a stop
> built in.  The pedestal/table top does not come out, even if the screw
> knob
> is removed completely.
>
> I also just lower mine into the "bed" position, cover it with an old towel
> or cardboard and lift the batteries out onto it.  But then, I haven't
> removed my batteries since spring 2002.
>
> -Jeff
>
>
> -----Original Message-----
> From: R Airis [mailto:rairis at comcast.net]
> Sent: Thursday, February 22, 2007 7:30 PM
> To: C320-List
> Subject: Re: [C320-list] Inside Table And Pedistal
>
> There is a screw knob by the base. loosen it and the table and the stand
> comes off as a unit.
> Bob......#266
>
>
>
>
> -- 
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.5.441 / Virus Database: 268.18.3/699 - Release Date: 2/23/2007
> 1:26 PM
>
>



____________________________________________________________________________________
Cheap talk?
Check out Yahoo! Messenger's low PC-to-Phone call rates.
http://voice.yahoo.com


-- 
No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.446 / Virus Database: 268.18.3/699 - Release Date: 2/23/2007 
1:26 PM