[C320-list] Bilge Spaces
Kirk McCullough
kirk.mccullough at telus.net
Sat Sep 22 15:30:58 PDT 2007
I go with hot water to flush out that line as we are washing down the
fridge. I haven't used bleach, but in a mild solution it might be good idea.
Kirk
#124
----- Original Message -----
From: "Darrell" <dgray at n-sea.org>
To: "C320-List" <c320-list at catalina320.com>
Sent: Monday, September 17, 2007 5:53 AM
Subject: Re: [C320-list] Bilge Spaces
> Thanks Kirk for the fridge drain plug idea, I will try that for starters.
> Do you ever run a little bleach down the fridge drain or into the shower
> sump or is that hard on hoses
>
> Darrell
>
>
> ----- Original Message -----
> From: "Kirk McCullough" <kirk.mccullough at telus.net>
> To: "C320-List" <c320-list at catalina320.com>
> Sent: Sunday, September 16, 2007 12:09 AM
> Subject: Re: [C320-list] Bilge Spaces
>
>
>> To me it seems you are getting more water in than I get. I don't have any
>> stanchion leaks, maybe that's the difference. I can't think of where you
>> would be getting all that water from. I have my fridge drain plugged and
>> unplug it and drain it into a jug when we wash down the fridge
>>
>> Kirk #124
>> ----- Original Message -----
>> From: "Darrell" <dgray at n-sea.org>
>> To: "C320-List" <c320-list at catalina320.com>
>> Sent: Thursday, September 13, 2007 5:42 AM
>> Subject: Re: [C320-list] Bilge Spaces
>>
>>
>>>I have the dripless seal, a new waterheater and holes drilled and plugged
>>>as per Catalina directions. With the fridge drain and numerous small
>>>leaks from stanchions etc. I suck a couple gallons out with my wet vac
>>>every couple weeks . I find it spreads out about an inch deep all the way
>>>from the engine to the knot meter sender unit and then turns into moldy
>>>slime if I leave it. Sure wish I had a proper sump on this boat. I cannot
>>>it took them so may boats to fix this problem. Some day I will have to
>>>save up and buy a later model,
>>>
>>> Darrell #88
>>> ----- Original Message -----
>>> From: "Kirk McCullough" <kirk.mccullough at telus.net>
>>> To: "C320-List" <c320-list at catalina320.com>
>>> Sent: Wednesday, September 12, 2007 7:34 PM
>>> Subject: Re: [C320-list] Bilge Spaces
>>>
>>>
>>>> Part of the issue is to keep water out of the 320. Install a dripless
>>>> shaft seal if you dont have one. It's a big improvement. Then vacuum
>>>> out that area once every 2-3 years to get out the water that may come
>>>> in from other sources.
>>>>
>>>> Kirk
>>>>
>>>> #124
>>>> ----- Original Message -----
>>>> From: "Jane & Ken" <obuoy4848 at sbcglobal.net>
>>>> To: "C320-List" <c320-list at catalina320.com>
>>>> Sent: Monday, September 10, 2007 5:50 AM
>>>> Subject: Re: [C320-list] Bilge Spaces
>>>>
>>>>
>>>>> Gary and Al, the first several hundred 320's built did not really
>>>>> have a "bilge" and there is space between the twolayers of fiberglass
>>>>> which allows water to collect and eventually that water finds its way
>>>>> into the hollow structual members where it cannot escape. The factory
>>>>> answer to this design flaw is to drill holes, vac the water out and
>>>>> plug the holes (then hope no more water gets in??). There are many
>>>>> pics on the web--or used to be-- I just raise the bow with a lifting
>>>>> strap, place all the weight (friends) I can in the aft cockpit, give
>>>>> them a beer and vac any water I have collected. I enlarged the
>>>>> inspection hole to 10 inches for easier access. I bought the boat new
>>>>> and have enjoyed sailing her and adding things as the years went by.
>>>>> Regards, Ken & Jane Cathey O'BUOY #219
>>>>>
>>>>> alahlm at comcast.net wrote: Gary
>>>>> I had the same problem with water collecting in the same spot I added
>>>>> a 6" inspection plate under the ladder to access the area and keep it
>>>>> dry -- there should be some pics on the web site
>>>>>
>>>>> al ahlman
>>>>> #476
>>>>>
>>>>> -------------- Original message --------------
>>>>> From: "Gary Magnuson"
>>>>>
>>>>>> On my 1995 320, (# 205) I was cleaning the bilge spaces and found
>>>>>> that the bilge
>>>>>> space under the sink, directly under the companion ladder, does not
>>>>>> drain into
>>>>>> the bilge. Isn't there supposed to be a connection between these two?
>>>>>> There
>>>>>> appears to be a limber hole, but it seems to be piped right past this
>>>>>> space. I
>>>>>> can only see into the space through the 4 inch hole under the port
>>>>>> floor
>>>>>> section. I used my wet vac to draw about 4 gallons out through the
>>>>>> inspection
>>>>>> hole. Any suggestions how to get this section to drain. I also notice
>>>>>> that the
>>>>>> compartment where the bilge pump is located, isn't the lowest point
>>>>>> in the
>>>>>> floor. Plan A was to wash and rinse each section and have it drain
>>>>>> aft to the
>>>>>> bilge pump. The water seems to drain forward toward the base of the
>>>>>> mast.
>>>>>> Thanks,
>>>>>> Gary Magnuson #205
>>>>>
>>>>>
>>>>>
>>>>> --
>>>>> No virus found in this incoming message.
>>>>> Checked by AVG Free Edition.
>>>>> Version: 7.5.485 / Virus Database: 269.13.16/1004 - Release Date:
>>>>> 9/12/2007 5:22 PM
>>>>>
>>>>>
>>>>
>>>>
>>>
>>>
>>>
>>>
>>> --
>>> No virus found in this incoming message.
>>> Checked by AVG Free Edition. Version: 7.5.487 / Virus Database:
>>> 269.13.21/1010 - Release Date: 9/15/2007 7:54 PM
>>>
>>>
>>
>>
>
>
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition. Version: 7.5.488 / Virus Database:
> 269.13.28/1023 - Release Date: 9/22/2007 1:27 PM
>
More information about the C320-list
mailing list