[C320-list] Spade anchor

[Bruce]

I was looking at a Spade but ended up going with a Mantus 35# they appear to be about the same size, the Mantus fit just fine.

"stord at cox.net" <stord at cox.net> wrote:

>Jim,
>
>I'm traveling, so will need to get home to confirm, but we bought the spade anchor sized for a 320 which the website says is the S80(33lb). It will fit on the bow roller and we've had no problem with the tip being near the bow. The shank is curved and the anchor does want to roll forward. I've got a line with a shackle on it to hold it in place, otherwise, it would probably "self launch."
>Steve
>S/VJoy  756
>Sent from my Verizon Wireless 4G LTE DROID
>
>jim brown <jbrown5093 at yahoo.com> wrote:
>
>>
>>
>>
>>
>>________________________________
>> From: jim brown <jbrown5093 at yahoo.com>
>>To: "C320-List at Catalina320.com" <C320-List at Catalina320.com> 
>>Sent: Tuesday, April 30, 2013 12:56 PM
>>Subject: Re: Spade anchor
>> 
>>
>>
>>Anyone know offhand if the 33 lb Spade Anchor will fit on the 320 roller and be self launching. I'm also concerned that the tip might be quite close to the hull when on the roller. I currently use a 22 lb Delta Fastset but was looking to add some weight and want to go to a spade design rather than a plow. 
>>
>>
>>Jim Brown
>>"Desafinado"
>>
>>
>>
>>________________________________
>> From: Don Dixon <donauw at bellsouth.net>
>>To: "C320-List at Catalina320.com" <C320-List at Catalina320.com> 
>>Sent: Tuesday, April 30, 2013 10:44 AM
>>Subject: Re: [C320-list] water heater
>> 
>>
>>Remove the access panel on the front of the heater.  Under the panel is a red reset button for the high temp limit breaker.  Push to reset.
>>
>>In my case, this did not work...needed to replace the heating element. 
>> You can order an element specificJim,
>
>I'm traveling, so will need to get home to confirm, but we bought the spade anchor sized for a 320 which the website says is the S80(33lb). It will fit on the bow roller and we've had no problem with the tip being near the bow. The shank is curved and the anchor does want to roll forward. I've got a line with a shackle on it to hold it in place, otherwise, it would probably "self launch."
>Steve
>S/VJoy  756
>Sent from my Verizon Wireless 4G LTE DROID
>
>jim brown <jbrown5093 at yahoo.com> wrote:
>
>>
>>
>>
>>
>>________________________________
>> From: jim brown <jbrown5093 at yahoo.com>
>>To: "C320-List at Catalina320.com" <C320-List at Catalina320.com> 
>>Sent: Tuesday, April 30, 2013 12:56 PM
>>Subject: Re: Spade anchor
>> 
>>
>>
>>Anyone know offhand if the 33 lb Spade Anchor will fit on the 320 roller and be self launching. I'm also concerned that the tip might be quite close to the hull when on the roller. I currently use a 22 lb Delta Fastset but was looking to add some weight and want to go to a spade design rather than a plow. 
>>
>>
>>Jim Brown
>>"Desafinado"
>>
>>
>>
>>________________________________
>> From: Don Dixon <donauw at bellsouth.net>
>>To: "C320-List at Catalina320.com" <C320-List at Catalina320.com> 
>>Sent: Tuesday, April 30, 2013 10:44 AM
>>Subject: Re: [C320-list] water heater
>> 
>>
>>Remove the access panel on the front of the heater.  Under the panel is a red reset button for the high temp limit breaker.  Push to reset.
>>
>>In my case, this did not work...needed to replace the heating element. 
>> You can order an element specific for this unit or just buy a 1000 (or was it 1200?) watt unit at Home Depot for $9.95.  
>>
>>Regards,
>>
>>Don Dixon
>>Stargazer, #605
>>Key West, FL
>>
>>Sent from my iPad
>>
>>On Apr 30, 2013, at 9:19, wflowe3 at aim.com wrote:
>>
>>> Did something stupid when opening up for spring (apparently spring is gonna last 3 days and then winter is coming back).  Filled all the water tanks, turned on the water heater (elec part) and waited for my hot water; it didn't come. After some mental trouble shooting, I remembered that I by-passed the water heater for winterization and I hadn't reconnected it.  So the heating element in the heater was heating air-not water. I don't think it liked heating air because once I plumbed the heater back in and it filled with water, still no hot water.
>>> 
>>> My question is  whether I
>> burned out the element or is there some sort of tripping safety feature that needs to be reset?  The breaker on the panel did not trip.
>>> 
>>> Bill
>>> Hull # 1146
>>> (2008)