[C320-list] Installing gas springs on 320 cockpit locker

[rclausen1 at bigpond.com]

Hi Neil

I am very interested in your article.

Regards

Teddy Clausen
Cool Change 294
Email rclausen1 at bigpond.com

-----Original Message----- 
From: kskis at aol.com
Sent: Monday, July 16, 2018 12:08 AM
To: C320-List at Catalina320.com
Subject: Re: [C320-list] Installing gas springs on 320 cockpit locker

Scott:  Here is the same response I sent Mike.  Very sorry for the delay. 
Most of the delay has been I had a problem describing the "location" of the 
brackets acurately without relying on the use of the specific 
brackets/bracket holes I used rather than any 10mm bracket.  I have asked 
Jeff Hare to help me finalize the article but I will send you a draft of the 
installation procedure with some pictures.  I would be happy to discuss by 
facetime or phone or email before you start drilling holes,etc.  Just please 
do not forward to anyone because I will be editing it before sending.  OK? 
My name is Neil Kornblatt  631 697-9037 kskis at aol.com  If you want to 
discuss send me a cell number.  Thanks.  Neil

In a message dated 7/15/2018 8:47:20 AM Eastern Standard Time, 
scottwestwood at bellsouth.net writes:


I too am interested in this.
Thanks,
Scott Westwood scottwestwood at bellsouth.net H (919)-362-8538    C 
(919)-618-7185

From: "mmellon at cruzio.com" <mmellon at cruzio.com>
To: C320-List at catalina320.com
Sent: Saturday, July 14, 2018 2:54 PM
Subject: Re: [C320-list] Installing gas springs on 320 cockpit locker

Hi Kskis (I don't have your real name, sorry).  I may have missed your
reply on this, but I'd really like to know the basics, the length and
model of the strut that worked, the location of the top mounting on the
locker lid, and the location of the bottom mounting.

I don't need much more.

Thanks.

Mike Mellon

mmellon at cruzio.com

On 2018-06-03 05:17, kskis at aol.com wrote:

> Hello.  I just completed installing a gas strut for the port cockpit 
> lazarette and I'm in the process of creating a description of the process. 
> Sorry to say other commitments have stalled the completion of my 
> description.  The key to the project is very much the location of the 
> brackets which took many tries.  I am new to the group and would 
> appreciate knowing the best way to post photos of the project once I have 
> them.  I would also like to make myself available for phone call and/or 
> facetime to anyone if I can avoid my personal information being made 
> public beyond the group. Neil Kornblatt "Harmony" Hull #973
>
> In a message dated 6/2/2018 4:54:42 PM Eastern Standard Time, 
> mmellon at cruzio.com writes:
>
> I am attempting to install gas spring struts on the port side lazarette
> cockpit locker lid, on LaVida, a 1996 C320. I think later 320 boats had
> these installed either as standard or as an option. The were also
> installed in several other length Catalina models that used the same or
> a similar locker lid.
>
> If someone has these gas struts installed on their boat, I would very
> much appreciate some information:
>
> 1. The manufacturer, part number, the extended length and the fully
> compressed length of the gas strut
>
> 2. The measured mounting location of the mounting bracket pivot pin on
> the underside of the locker lid, measured from the hinge pin
>
> 3. The mounting location of the lower mounting bracket - this is
> normally slightly below the edge of the cockpit seat.
>
> Many thanks to the group for any assistance.
>
> Mike Mellon
> LaVida Cat320 #324 1996