[C320-list] New Propane tank & now need new supply pig tail, regulator & gauge.

[Guy Smith]

Hey Bob,
I had a catastrophic gas failure in 2019 and replaced the bottle, regulator
and solenoid as a result. The new parts are recommended as the original
1997 gas parts have had failures similar to what my wife and I experienced.
It was a very scary situation that ended without a fireball! I've copied
the original emails below.
~g

Guy & Liz Smith
sv Pleiades
'97 C320 #452
Worton Creek, MD
----- Forwarded Message -----
*From:* Guy Smith <smitski2001 at yahoo.com>
*To:* Catalina List <c320-list at catalina320.com>
*Sent:* Thursday, October 3, 2019, 05:51:56 PM EDT
*Subject:* Re: Major LP gas system failure!

Hey All!

An update on the gas leak on Pleiades....

I got the Tank, Regulator, Solenoid and Hose off the boat pretty easily.
The Tank, Regulator and Solenoid are available as OEM replacements from
Catalina Direct. Customer Tech Support  was awesome.

The hose runs through a conduit more or less under the Port cockpit locker,
under the Refer and lower stove shelf and exits beside the Hot Water heater
under the sink.
It slid out pretty easily with a piece of the line tied and taped around it
so I can pull the new hose through.

I took the hose home and connected one end to a stop valve and the other to
the gas bottle to pressure check it since there was no obvious blowouts or
damage to it.
Turns out the hose was not the leak... :(  ...I plan on replacing it
anyway...

So now I need to rig up a temporary connection to the stove with my
portable compressor and pressurize it to see what's leaking in it's
components....
I don't see any obvious rubber parts in it, so I'm baffled as to what might
be the culprit. Might be a threaded fitting that blew out?

The hose is not directly available via Catalina Direct, but he said he
could get one made for me. It's 17 1/2 foot long. I'm thinking I can find
one or get one made local.
I'll call around tomorrow to see what I come up with.

Anyone have to replace parts in their stove?

Best Regards,
~g

Guy and Liz Smith
sv Pleiades
'97 C320 #452
Worton Creek, MD


On Tuesday, September 3, 2019, 07:24:43 PM EDT, Guy Smith <
smitski2001 at yahoo.com> wrote:


Hey All!

Had some excitement on Sunday morning, on the hook in Still Pond!
I got up first to start the tea pot on the stove in the galley.
(My wife was still snoozing a bit...)
As I usually do, I ventured out
into the cockpit and turned the LP tank on... instead of the normal 1/4
second "psst" of the
gas bottle charging the gauge up to pressure, I (we actually) heard a POP!
and the gas bottle
continued to "pssssssssssss..."! I immediately turned the valve off and
headed into the cabin.
There was a heavy oder of gas in the galley area. Needless to say, no stove
valves were left on.
The I realized that I hadn't switched the gas solenoid switch on, so I was
amazed that gas made it into the cabin!

Some friends that I've been talking with think that the pressure regulator
failed and the gas valve solenoid
(down stream of the regulator) was a low pressure solenoid and couldn't
take the pressure (which was
about 30 psi at the time, if you could believe the gauge).

I can't help thinking that if I would have got a burner started and *then*
the system failed with the burner lit,
it coulda been really BAD! Especially since my wife was in the aft cabin
and couldn't egress very quickly!
I think my first reaction would've been to go to the control panel to turn
the solenoid switch off,
loosing precious time getting to the bottle valve.

So I was wondering:

-Anyone else have this happen to them?
-Could the Stove be damaged after getting a jolt of hi-pressure gas?
(obviously *something* leaked in the cabin)
-Since I'm gonna replace the tank (it's  a '97 original), regulator and
solenoid,
should I also pull a new gas line or just pressure check it? It seems
pretty involved to fish a new one
but probably a good thing to do?
-How would I pressure check the stove components? Is there recommended
pressure to set and monitor for leaks in the stove's components?
-Am I technically allowed to do this work myself without certification?

I'm a pretty capable mechanic and have run and repaired gas lines in my
home, so I'm not against doing the work myself.
I can imagine the yard would charge me an arm and a leg to diagnose and
repair the system before they were done.

Thoughts?
~g

Guy and Liz Smith
sv Pleiades
'97 C320 #452
Worton Creek, MD


On Mon, Mar 7, 2022 at 8:57 PM Bob Borelli <cassattc22 at hotmail.com> wrote:

> Holy Smokes!  I did it!  Thank you!
>
> You know my wife rides horses & I sail boats.
>
> We are getting there, computer wise.
>
>
> ________________________________
> From: C320-list <c320-list-bounces at lists.catalina320.com> on behalf of
> Jeff Smith <svsailmates512 at gmail.com>
> Sent: Monday, March 7, 2022 8:44 PM
> To: C320-List at catalina320.com <C320-List at Catalina320.com>
> Cc: c320-list at lists.catalina320.com <c320-list at lists.catalina320.com>
> Subject: Re: [C320-list] New Propane tank & now need new supply pig tail,
> regulator & gauge.
>
> Bob,
>
> The photos are available where you uploaded them.
>
> Cheers,
> Jeff
> Fledgling Webmaster
>
> > On Mar 7, 2022, at 4:27 PM, Bob Borelli <cassattC22 at hotmail.com> wrote:
> >
> > I replaced the original 1994 10lb Aluminum propane tank with a new
> Worthington Aluminum LPG Cylinder 10lb (2.4 gal) Vertical from West
> Marine.  The new tank is about 3/4" shorter than the old tank so I used
> 3/4" Starboard to raise it up in order to connect the Supply Assembly.
> >
> > I would like to replace this assembly, the regulator, gauge, pigtail and
> assorted threaded fittings.
> > It is a very tight space inside the propane locker.
> > No room for an inline Acme threaded connection and valve.
> >
> > Has anyone replaced this assembly with new parts?
> > One email on the list states a local propane shop used this existing
> assembly as a template to put together a new one.
> > I like that idea!!!
> >
> > Any suggestions, experience most appreciated.  Please help!
> > I have attempted to upload a picture of the top of the tank in the
> locker with the supply assembly.
> >
> > Thank you!
> >
> > Bob Borelli  C320 no. 209 'Elusive'  SAI on the Sassafras River, MD
> >
>
>