[C320-list] Interior Table

[Tom Grass]

After starting this thread, just want to mention that the fill in cushion
on Bucket List fits perfectly.  Thanks again for all your help.

Tom Grass
S/V Bucket List

On Mon, May 27, 2024, 9:31 AM Dave Hupe via C320-list <
c320-list at lists.catalina320.com> wrote:

> So, obviously I am not alone where the filler cushion is not thick enough
> and/or the table goes to low. It is ridiculous to need to come up with such
> "fixes" like having another piece if foam around.
> I am going to try to figure out a fix to prevent the table from going down
> as low like John mentions.
> Dave Hupe
> 1994 C320 #32
>
> Yahoo Mail: Search, Organize, Conquer
>
>   On Mon, May 27, 2024 at 8:39 AM, John Beck via C320-list<
> c320-list at lists.catalina320.com> wrote:   On my table, I put a 1  1/2
> inch piece of foam under my table cushion, ie:
> yoga mat. I also put a folding leg on  each end  so now I can  move around
> on it without worrying about it popping screws
> John Beck
> Sv Sail On
> Hull #518
> Jb
>
>
> On Sun, May 26, 2024 at 1:52 PM John Frost via C320-list <
> c320-list at lists.catalina320.com> wrote:
>
> > How about adding a spacer under the table around the tube that
> compresses?
> > It would act like a giant spacer washer and not allow the tube to fully
> > compress. You could find something at the hardware store or make one out
> of
> > plywood by drilling an appropriate-sized hole in a round piece, lifting
> the
> > table off, and sliding your "washer" on.
> >
> > Speaking of tables, we don’t use it as a bed and found it took up too
> much
> > room as a table so we got a small one at a boat show. I took the mount
> off
> > of our large table and screwed it to the new. The twist that I wanted to
> > mention is I put the mount about 6 inches off center. I can create more
> or
> > less room for a diner by lifting the table, rotating it a bit and putting
> > it back on the pedestal
> >
> >
> > John
> > 2007 C320MKII
> > Hull  #1118
> > Lake Guntersville, AL
> >
> >
> >
> >
> >
> > -----Original Message-----
> > From: C320-list <c320-list-bounces at lists.catalina320.com> On Behalf Of
> > Dave Hupe via C320-list
> > Sent: Sunday, May 26, 2024 10:51 AM
> > To: c320-list at catalina320.com
> > Cc: Dave Hupe <hoopdtwo at yahoo.com>
> > Subject: Re: [C320-list] Interior Table
> >
> >  So, while we are on this topic ..... my table lowers/raises fine, but
> > when down my filler cushion area (definitely thinner than the other
> > cushions) on top of the table winds up being low.  So, it does not form a
> > nice flat expanded bed.  We wind up putting items (blanket, etc.) beneath
> > the filler cushion to try to even it out. I suppose i could push the
> table
> > down just enough to make it level and turn the knob/lock, but I was
> > concerned the table would slip down when weight is placed on it (the knob
> > doesn't seem to lock into a hole in the post to keep it at the desired
> > level. Does anyone else experience this issue ...... any "fixes" to
> > suggest??
> > Dave Hupe
> > 1994 C320 #32
> >
> >
> >
> >
>
>