[C320-list] Engine (not) starting
Bruce Heyman
bruceheyman at cox.net
Fri Aug 16 17:57:14 PDT 2013
David,
If you have a DVM you could check for voltage in the control box. There is a schematic in the manual.
Bruce
Somerset Dana Point CA
Bruce Heyman
(949) 289-8400
david.allred at verizon.net wrote:
> I think I found the inline harness fuse, fairly easily accessible from
> the front of the engine on the port side. It is a small, two-pronged
> fuse that plugs into a black holder. Unfortunately for me, that fuse
> (I think a 1 amp) was fine as was a similar 10 amp fuse in the same
> kind of holder located close to the first one (it was fine, too). I
> did not see any other fuses near the engine. Could there be another
> one somewhere between the pod and the one I found? At any rate, I will
> continue to pursue the problem rather than abandon my boat because I
> can't start the engine.
> DLA
>
>
> On 08/16/13, clburti at gmail.com wrote:
>
> That inline harness fuse is on the port side of the engine.
> Fair Winds
> Chris Burti
> Commitment
> Catalina 320, #867
> From: Irving Grunes
> Sent: �Friday�, �August� �16�, �2013 �3�:�39� �AM
> To: [1]C320-List at catalina320.com
> I think there is an inline fuse in the wiring harness in the cableing
> going
> to the pod.
> Also check the connections at the terminal block of that cabeling in
> the pod
> irv grunes
> 2001 #851
> On Fri, Aug 16, 2013 at 1:49 AM, [2]fred.lecuyer at live.com <
> [3]fred.lecuyer at live.com> wrote:
> > I think there is a fuse in the pod where you were. Check inside the
> pod.
> >
> > Fred
> > #960
> >
> > Sent from my HTC Inspire� 4G on AT&T
> >
> > ----- Reply message -----
> > From: [4]david.allred at verizon.net
> > To: <[5]C320-List at Catalina320.com>
> > Subject: [C320-list] Engine (not) starting
> > Date: Thu, Aug 15, 2013 7:34 pm
> >
> >
> > My boat is #712 , a 2000 model. The engine is a Yanmar 3GM30F.
> > DLA
> >
> >
> > On 08/15/13, Williamyahoo.com> wrote:
> >
> > What make on engine do you have ? What year is your boat?
> > Mike Ott
> > Sent from my iPhone
> > On Aug 15, 2013, at 6:56 PM, [1][6]david.allred at verizon.net wrote:
> > > Today I replaced my temp gauge. The engine cranked as usual, but
> the
> > > gauge did not appear to work. I took the face off the backing and
> > > fiddled with the gauge connections. When I attempted to start the
> > > engine again, it would not start--nothing at all when I pressed the
> > > start button and I noticed that all the gauges were dead with the
> key
> > > on. Apparently, there is no electricity going to the control panel.
> I
> > > depressed the 10 amp breaker switch at the bottom of the panel, but
> > > still nothing. The batteries are good and the RayMarine instruments
> > as
> > > well as everything in the cabin are working. Can you suggest what I
> > > may do? Is there another fuse/relay breaker somewhere? Thanks.
> > > DLA
> >
> > References
> >
> > 1. [7]mailto:david.allred at verizon.net
> >
> >
>
>References
>
> 1. mailto:C320-List at catalina320.com
> 2. mailto:fred.lecuyer at live.com
> 3. mailto:fred.lecuyer at live.com
> 4. mailto:david.allred at verizon.net
> 5. mailto:C320-List at Catalina320.com
> 6. mailto:david.allred at verizon.net
> 7. mailto:david.allred at verizon.net
More information about the C320-list
mailing list