[C320-list] Prop

[Warren Updike]

The tranny ratio is probably the same for boats with same engine and prop. 

-----Original Message-----
From: Martin Rosenberg [mailto:martinlrosenberg at gmail.com] 
Sent: Monday, November 25, 2013 6:49 PM
To: C320-List at catalina320.com
Subject: Re: [C320-list] Prop

Good idea, I'll try that. My problem appears to be paint that is so thick
that you can't differentiate the imprint but maybe the chalk will help.
Martin Rosenberg
"Avalon"   #823


On Mon, Nov 25, 2013 at 3:40 PM, Colin Evans <twosailors at bigpond.com> wrote:

> I had the same problem with the hose in the way.   I rubbed ours with
> chalk,
> then took a picture of it with my phone.  It is 2.21 on ours
> *************************
> Regards
> Colin Evans
> Watermark
> 2000 C320 # 774
> Lake Macquarie, Australia
>
>
>
>
>
> -----Original Message-----
> From: c320-list-bounces at lists.catalina320.com
> [mailto:c320-list-bounces at lists.catalina320.com] On Behalf Of Martin 
> Rosenberg
> Sent: Tuesday, 26 November 2013 7:24 AM
> To: C320-List at catalina320.com
> Subject: Re: [C320-list] Prop
>
> Bruce,
>   How did you do a pencil rubbing? The exhaust hose is only about an 
> inch from the transmission on my boat so I can barely get in there. I 
> really don't want to remove the hose just to read the plate.
>   That would be worse than when I had to remove the vent hose and 
> unscrew the fitting on my waste tank so I could see how full it was. 
> BTW, the previous owner had stored the boat for the winter with a FULL
tank.
> Martin Rosenberg
> "Avalon"  #823
>
>
> On Mon, Nov 25, 2013 at 12:50 PM, Bruce Heyman <bruceheyman at cox.net>
> wrote:
>
> > Diane,
> > This summer I did some serious maintenance on my Yanmar, including
> chasing
> > all the rust and repainting  (I now insist that everyone that comes 
> > on board has to ogle the engine.  My wife would love it if I would 
> > put the engine covers back on).  The ratio is stamped on the back of 
> > the transmission.  I didn't realize that it was until I had stripped 
> > all the paint off to clear up bad corrosion in that area.  Before 
> > you remove the paint (unless you too have corrosion there) you might 
> > try doing a pencil rubbing.  Mine was 2.21 (from memory) and we have a
2000.
> > Good luck,
> > Bruce
> >
> > Bruce Heyman
> > bruceheyman at cox.net
> > (949) 289-8400
> > Somerset #671 Dana Point, CA
> >
> > -----Original Message-----
> > From: c320-list-bounces at lists.catalina320.com [mailto:
> > c320-list-bounces at lists.catalina320.com] On Behalf Of Diane Fowler
> > Sent: Monday, November 25, 2013 6:29 AM
> > To: C320-List at Catalina320.com
> > Cc: C320-List at catalina320.com
> > Subject: [C320-list] Prop
> >
> > We are trying to buy a flex oh fold Prop, and the manufacturer wants to
> > know if our gear reduction is one 2.  21. or one  2.   62.   #948.
> Yanmar.
> > 3gm.   Anyone know ???  Thanks,  captain Diane
> >
> > Sent from my iPhone
> >
> > > On Nov 25, 2013, at 9:25 AM, "Brian/Carol McLamb" <
> bjcnmclamb at gmail.com>
> > wrote:
> > >
> > > Hello Graeme.  I have not physically measured it myself, but our 
> > > marina
> > and
> > > those I travel to use 33 ft.  I believe it is closer to 32 ft 4" 
> > > in actuality.  Brian s/v Serenity # 1075 out of Oriental, NC.
> > >
> > >
> > >> On Mon, Nov 25, 2013 at 9:16 AM, Graeme Clark <cg at skyflyer.co.uk>
> > wrote:
> > >>
> > >> Has anyone actually measured their 320 end to end to get a true 
> > >> LOA including the pulpit and projection at the rear of the 
> > >> boarding
> ladder.
> > >>
> > >> I just ask because my marina is trying to charge us based on 10.4
> metres
> > >> (34ft 1.5") which they claim they have measured which seems a bit 
> > >> on
> the
> > >> high side to me!
> > >>
> > >> I'm 250 miles away so can't just nip down to the yard and measure it!
> > >>
> > >> Thanks
> > >>
> > >> Graeme
> > >> #303, Simia, 1996
> >
> >
>
>