[C320-list] Rocna 15 Anchor Fit on Early C320s - Hull 268

[Ted Harrison]

Thanks Myron

Ted Harrison

> On Mar 26, 2018, at 12:09 AM, Welch, Myron D <myron-welch at uiowa.edu> wrote:
> 
> Warren,
> 
> I made that upgrade at least 15 years ago, so I don’t remember all the details. The nuts are easily accessible in the anchor locker and the bolts came off without a fight. There were bolt holes in the new roller, but I don’t know if they lined up with the previous holes. Since the old holes are covered by the new roller, I would have just filled the old holes with caulk and drilled new holes to match the new bolt hole patterns. I either used the old backing plates or made new ones. Again, very easy to access and fit either way. 
> 
> Ted, it was difficult to pry off the old roller as I too believe it was bedded with 5200. I just dug out as much material as I could and then wedged a pry bar between the bottom of the roller and top of the deck. Each time the roller lifted a bit I would cut more caulk with a thin chisel. With patience, the gel coat survived. Good luck.
> 
> Myron Welch
> Wind Instrument #238
> Iowa City, Iowa
> Grace Memorial Harbor
> Elk Rapids, Michigan
> 
> 
> 
>> On Mar 25, 2018, at 3:22 PM, Warren Updike <wupdike at hotmail.com> wrote:
>> 
>> Myron, I considered replacing the anchor roller on our 1995, #62, but chickened-out because the bolt holes didn't line-up, and I was concerned as to whether the nuts and backing plate were loose or built into the structure. Can you help us with that? 
>> 
>> Warren and Pattie Updike
>> 1994 C320 "Warr de Mar" #62
>> Middle River, MD (Chesapeake Bay)
>> 
>> -----Original Message-----
>> From: Welch, Myron D [mailto:myron-welch at uiowa.edu] 
>> Sent: Saturday, March 24, 2018 10:30 PM
>> To: C320-List at Catalina320.com
>> Subject: Re: [C320-list] Rocna 15 Anchor Fit on Early C320s - Hull 268
>> 
>> Cliff,
>> 
>> Several years ago I replaced the old shorter anchor roller on my 1995, #238, with a longer Windline model to fit my Bruce 33. The change was quite easy. 
>> 
>> Myron Welch
>> Wind Instrument #238
>> Iowa City, Iowa
>> Grace Memorial Harbor
>> Elk Rapids, Michigan 
>> 
>> Sent from my iPad
>> 
>>> On Mar 24, 2018, at 8:09 PM, Cliff Lee <rcliffordlee at gmail.com> wrote:
>>> 
>>> After much consideration, I bit the bullet and bought a Rocna 15 to replace
>>> my CQR.  I had seen past C320 list discussions about the likelihood that
>>> the anchor roller bail would be too small for early C320 models and indeed
>>> it is about 1" too short to fit the Rocna shank.  No problem to buy a
>>> taller bail.  However, I was surprised to find that the anchor roller
>>> itself is so short that the tip of the anchor in the secured position
>>> overlaps and lies up against the bow by at least 3-4".  I had not seen that
>>> issue on previous discussions.  I am wondering if I have an unusually short
>>> anchor roller.  Mine is a Windline model and is about 20" from tip to tip,
>>> with the roller hub itself about 3" from the tip of the assembly.  Any
>>> thoughts out there about whether I need a longer anchor roller, the length
>>> of your rollers (and your hull number), or other solutions?  At this point,
>>> I'm afraid I may have to return the anchor.  Even if I can protect the hull
>>> against the anchor tip, it will still bang against the hull and drive us
>>> crazy.  Thanks for any guidance you can offer.
>>> 
>>> Cliff Lee
>>> Comfort Zone - 1995 Hull 268
>