[C320-list] Perkins m30 raw water pump

[Dan Winsor]

Another owner rebuilder here. EZ job, very rewarding to work on a robust
piece of gear instead of throw-away junk.

Dan Winsor
Lucky Devil #109 1994

On Sun, Oct 6, 2024 at 5:02 PM Dave Hupe via C320-list <
c320-list at lists.catalina320.com> wrote:

> I had my Jabsco 29450-1101 seawater pump completely rebuilt for $277 in
> 2017 by Depco Pumps  http://www.depcopump.com/contactus.php  .The cost
> could have been about $160 less if the shaft had not been scored and needed
> to be replaced.
> If you don't  feel comfortable rebuilding by yourself, contact Depco and
> inquire.
>
>
> Dave Hupe
> 1994 C320 (#32)
> Yahoo Mail: Search, Organize, Conquer
>
>   On Sun, Oct 6, 2024 at 11:46 AM, Gregg Baklund<gb.sailfun32 at gmail.com>
> wrote:   Thank you all for your help
> I did find a few remaining original Jabsco pumps available in Florida
> $1,000 which seems to built better than the Ancor brand at a lower cost. I
> will focus on rebuild first.
>
> Gregg Baklund
> 206 402-8896
> Sent from my iPhone
>
> > On Oct 5, 2024, at 6:45 AM, Dave Hupe via C320-list <
> c320-list at lists.catalina320.com> wrote:
> >
> > 
> > $50 rebuild kit
> https://parts4engines.com/collections/perkins-perama-m30-parts/products/perkins-perama-m30-raw-water-pump-impellers-service-kits?variant=44338960367857
> > Dave Hupe
> > 1994 C320 #32
> >
> > Yahoo Mail: Search, Organize, Conquer
> >
> >  On Sat, Oct 5, 2024 at 9:17 AM, Jeff Smith via C320-list<
> c320-list at lists.catalina320.com> wrote:  Larry,
> >
> > I used a bearing press kit for front wheel drive vehicles, if I recall
> correctly. That, or I used a socket that matches the outside of the
> bearings and a hammer (I also did my wheel bearings on my Ridgeline at the
> same time, so I may be conflating the two when I say I used the front wheel
> bearing press kit). I used a micrometer to measure the distance. I had a
> small amount of water in the engine bilge and a patina on the water pump. I
> bought the rebuild kit from Parts4Engines.
> >
> > Jeff
> >
> >> On Oct 5, 2024, at 9:01 AM, WindSwept via C320-list <
> c320-list at lists.catalina320.com> wrote:
> >>
> >> Jeff - how did you press the bearings?
> >>
> >> Larry
> >> 1995 #246
> >>
> >>>> On Oct 4, 2024, at 8:49 PM, Jeff Smith via C320-list <
> c320-list at lists.catalina320.com> wrote:
> >>>
> >>> I rebuilt my pump several years ago, and it works fine. Pressing the
> >>> bearings can be tricky, though. It is a much cheaper repair.
> >>>
> >>> Good luck,
> >>> Jeff
> >>> ‘94, #121
> >>>
> >>>> On Fri, Oct 4, 2024 at 9:02 PM Dave Hupe via C320-list <
> >>>> c320-list at lists.catalina320.com> wrote:
> >>>>
> >>>> I bought a rebuild kit like this
> >>>> https://www.dieselpartsdirect.com/je294501201mnk, and my pump is
> working
> >>>> pretty well now.
> >>>> David Dines
> >>>> “Teal Heron”94 C320 #144Beverly, MA
> >>>> Yahoo Mail: Search, Organize, Conquer
> >>>>
> >>>> On Fri, Oct 4, 2024 at 6:18 PM, Gregg Baklund via C320-list<
> >>>> c320-list at lists.catalina320.com> wrote:  I need to replace my raw
> water
> >>>> pump on my ‘95 Perkins M30
> >>>> I have a Jabsco 29450-1201 pump. It looks like these are hard to come
> by.
> >>>> Any leads on where to purchase in the states?
> >>>> Thanks
> >>>>
> >>>> Hull 228
> >>>> SV Paradise
> >>>> Seattle
> >>>> Gregg Baklund
> >>>> 206 402-8896
> >>>> Sent from my iPhone
> >>>>
> >>
> >
> >
>
>